AGAZINENTERWEAVELLC. that the bead chain with the drop bead has 6beads, including the drop.You will always join this chainat the outside cord of the second bead over on the previ-ous chain.
The second chain has 5 beads, and you will al-ways join it at the outside cord of the third bead over onthe previous chain.The extra bead in every other chainbecomes the bottom edge and causes the necklace to gen-tly curve.Pull each chain tight so that the necklace willRepeat Chain 1 and Chain 2 for a total of 35 pairs ofchains.You should have 9 beads left on the spool cord.Forthe final chain, which is your clasp-loop that will connectover the button, cast on 2ds, the remaining beads with 2dsbetween the beads, 2ds.Pull into a chain.To center theloop, join this chain at the outside cord of the third beadover on the previous chain.After joining the final chain,tie multiple overhand knots and cut both cords, leaving a-inch (6-mm) tail.Melt the ends so that the cord ballsup close to the knot (if the cord becomes dark, file the darkspot with an emery board or paint a bit of cream-colorednail polish on the dark spot).To attach the button, thread the beading needle withabout 1 yard (1 m) of Nymo thread; double the thread,knot the ends together, and trim the tails.
Pass down ontothe top side of the inner part of the initial ring.Pass backup at the same place and string 1 size 6 seed bead and thebutton so that the button face is pointing upward.String4 size 11 seed beads and pass the needle down the secondhole on the button and down through the size 6 seed beadinto the tatting.
Come back up and attach 4 more size 11seed beads.
Do this a total of three times to tightly con-nect the buttonholes.When going down for the third andfinal time, weave the needle away from the button into thetatting stitches and to the edge of the chain.
Tie a half-hitch knot and weave back into the tatting to the otherside.Tie two more half-hitch knots and weave into thecenter before cutting the thread.BraceletPrestring 135 raindrop beads on the cord; add morefor a longer bracelet.
Pull 1 yard (.9 m) of cordthrough the needle eye to become the core cord.As withthe necklace, begin the bracelet by making a ring.Afterthat, you will make chains, but the bracelet has only onechain pattern repeated
.Ring: Cast on 2ds, 1b, 2ds, 1b, 2ds, 1b, 2ds, 1b, 2ds, 1b,2ds, 1b, 2ds (6 beads total).Pull into a ring, and tie anoverhand knot.: Cast on 2ds, 1b, 2ds, 1b, 2ds, 1b, 2ds, 1b, 2ds,1b, 2ds (5 beads total).Pull into a chain, and join to theprevious ring counting two beads over from the base ofthis chain.Tie an overhand knot around the spool cord.Repeat 22 times for a 6-inch (16.5-cm) long bracelet;the bracelet will stretch a bit after setting the stitches inhot water.Always count two beads over for each join.Forthe final chain, which is your clasp-loop, cast on 2ds, theremaining 9 beads with 2ds between the beads, 2ds.Pullinto a chain.To center the loop, join the last chain at theoutside cord of the third bead over on the previous chain.Finish the ends and add one button as for the necklace.To set the stitches, soak both pieces in very hot waterfor a few minutes, arrange the necklace in a curved shape,spread them out on a flat surface, and allow to dry com-pletely.The heat causes the stitches to tighten upandposition the beads.BOUTTHEEsther Trusler has been playingwith beads for the past five or so years.She teaches classesat the local bead store in her town; visit the store's websitewww.ezknit.com.Trusler's beadwork may be seen illustrations by Dustin Wedekind.Editors note: Please see the next page for our Needle Tattingwith Beads How-To.AGAZINENTERWEAVELLC.
First Thread Your Needle - Shamanic Art And Craft By …
10 beads (the normal size of bead found in most craft and sewing shops), ... Start by threading your beading needle, which is often a task in it’s own right. (nicholaswood.net)
From 5 Free
Size 10 beading needle Scissors. Crystal Radiance Brooch Tina Koyama presented by beadingdaily 10 Beading Patterns from beading daily: 5 free brick stitch beading … (nicholaswood.net)
Embellishments For Your Costuming - Timeless Creations | Sine ...
size 16 (quite thin) beading needle hold on to it carefully. Size 10, 12, and 13 fit the popular 11/0 seed bead (and more). Size 15 will fit the smaller 15/0 (nicholaswood.net)
and Braceletwith BeadsEsther Trusler's tattednecklace and braceletPhotograph by Joe Coca.eedle tatting is a gentle art that can be traced as far back as the 1850s.Some believe that tatting developedfrom netting and decorative ropework created by sailors and fishermen.If you are new to needle tattingwith beads, see the sidebar below.
For another bead needle tatted project, see the April/May 2004 issue ofPieceWork's sister magazine BeadworkTRIALOFFERDiscover projects and articles sure to inspire and expand yourcreative horizons.From cover to cover,PieceWorkmagazine gives you gorgeous photography,amazing needlework objects,contemporary projectswith a historical perspective,and the personal stories ofneedle-workers from around the globe.PieceWorkmagazine also brings you articles on beautiful heir-loom-quality projects,and the personal stories and memoriesbehind timeless pieces ofhandwork.Dont miss out on anotherissue.Take advantage ofthis special risk-freeoffer today!Cal800800ode JPDP6,or go to.interweave.com/go/pwkJPDP6.
First thread your needle.
Tags: embroidery needles size chart,how to choose beading thread,how to use beading needles,beading thread size chart,beading needles sizes,